General Specifications

(1)Power supply

• 100 V ( - 15%) to 240 V (+ 10%) AC,
• 50/60 Hz
• 24 V (± 10%) DC. 24 V (± 10%) AC,
• 50/60 Hz.
  
  
• (2)Power consumption:
12 VA MAX.

(3)Insulation resistance:

• 20 MΩ MIN. (at 500 V DC)

(4)Withstand voltage:

• Power source ⇔ all terminals
  1500 V AC for 1 min
• Relay contact output ⇔ all terminals
  1500 V AC for 1 min
• Between others 500 V AC for 1 min

(5) Approvals and certification:

• UL(UL873), C-UL(CSA C22.2 No.24-93 or
• equivalent), CE mark(LVD : EN61010-1,
• EMC : EN61326-1)
  
  

Input section

Process value input

• (1) Number of inputs :1 point
• (2) Input setting: Programmable scale
• (3) Input signal: See Table 1 (thermocouple, resistance
  bulb, mV, voltage, current (With external
  250Ω resistance) universal input)

(4) Standard measurement range and input type:

(5) Indication accuracy (at Ta = 23°C) :

• Thermocouple input: ± 0.3%FS ± 1 digit
    ± 1°C or ± 2°C, whichever greater *except:
• Thermocouple B, 0 to 400°C
  ± 5 %FS ± 1 digit ± 1°C

• Thermocouple R, 0 to 500°C
     ±1%FS ± 1 digit ± 1°C
• Thermocouple T, -200 to 0°C
     ±0.5%FS± 1 digit ± 1°C
• Resistance bulb input: ± 0.3%FS ± 1
     digit or ± 0.5°C, whichever greater
• mV input, voltage input, current input:
     ± 0.3%FS ± 1 digit

(6) Indication accuracy by change of temperature:

• ± 0.3%FS/10°C

(7) Indication resolution:
(8) Input sampling cycle:

• 200 ms

(9) Input impedance:

• Thermocouple, mV input: 1 MÙ MIN.
• Current input: 250 Ù
• Voltage input: About 1 MÙ

(10) Variation by signal source resistance:

• Thermocouple, mV input: ± 0.3%FS ±
  1 digit per 100 Ù
• Voltage input: ± 0.3%FS ± 1 digit per
  500 Ù

(11) Allowable wiring resistance:

• Resistance bulb: 10 Ù MAX. (per wire)

(12) Allowable input voltage:

• DC voltage input: Between +35 and
  - 10 V
• Current input: Within ± 25 mA
• Thermocouple, resistance bulb, mV input:
  Within ± 5 V

(13) Noise rejection ratio:

• Normal mode: 40 dB (50/60 Hz)
• Common mode: 120 dB (50/60 Hz)
  From ground, at 220 V AC, 50/60 Hz
  Between input and output, at 220 V AC,
  50/60 Hz

(14) Input correction:

• (a) User adjustment: Zero point, span
  ± 50%FS for each
• (b) Process value shift: ± 10%FS
• (c) Input filter: 0.0 to 120.0 sec (filter OFF
  if set at 0.0)

(15) Overrange, underrange:

• Beyond range of -5 to 105% (accuracy
  not guaranteed between -5 and 0, and between
  100 and 105%FS)

2.2 Auxiliary analog input (remote SV input)

• (1) Number of inputs: Up to 1 point
• (2) Input signal: Voltage, 0 to 5 V DC /1 to 5 V DC
• (3) Input impedance:
• About 1 MÙ
• (4) Sampling rate: 800ms

2.3 Heater current detector (CT) input

• Input type: Single phase CT Up to 1 point
• For 1 to 30 A: CTL-6-S-H
• For 20 to 50 A: CTL-12-S36-8F

(2) Range of detected current: 1 to 50A
(3) Detected current accuracy:Setting ± 10%FS
(4) Detected current resolution0.1 A
(5) ON time necessary for detection:800 ms MIN.

2.4 Digital input (DI)
(1) Number of points: 2 points (up to 3 points for motorized valve control output)
(2) Specifications: No-voltage contact or transistor input
(3) Contact capacity: 30 V DC, about 3 mA (per point)
(4) Input judgment: ON assumed at 1 kÙ or lower (contact) or
     5 V DC or lower (transistor)
     OFF assumed at 100 kÙ or higher (contact)
     or 18 V DC or higher (transistor)

(5) Sampling pulse width: 200 ms MIN.
(6) Functions: Remote mode selection, SV changeover,
      control standby, AT startup, timer startup,
      alarm unlatch, Program selection, start /
      stop / reset, PID switching (normal/reverse)

Output section

3.1 Control output
(1) Number of points: Up to 2 points (2 points: Heating/cooling
     control)
(2) Type: selected out of [1] to [5] below [1] Relay contact output

• Proportional cycle: 1 to 150 sec
• Contact structure: 1 NO (SPST) contact
• Contact capacity: 220 V AC/30 V DC, 3 A (resistive load)
  220 V AC/30 V DC, 1 A (inductive load)

• Minimum ON/OFF current: 100 mA
  (24 V DC)

• Mechanical life: 20 million operations
  MIN. (100 operations/min)

• Electrical life: 100,000 operations MIN. (rated load)

[2] SSR/SSC drive output

• Proportional cycle: 1 to 150 sec
• ON voltage: 20 V DC (18 to 24 V DC)
• OFF voltage: 0.5 V DC or lower
• Maximum current: 20 mA DC (for each of outputs 1 and 2)

• Load resistance: 850 Ù MIN.

[3] Current output (0 to 20 mA DC/4 to 20 mA DC)

• Accuracy: ± 5%FS

• Linearity: ± 5%FS
• Load resistance: 600 Ù MAX.

[4] Voltage output (0 to 5 V DC/1 to 5 V DC/0 to 10 V DC/2 to 10 V DC)

• Accuracy: ± 5%FS
• Linearity: ± 5%FS
• Load resistance: 10 kÙ MIN.

3
[5] Motorized valve control output

• Contact structure: 2 NO (SPST) contacts
• Contact capacity: 220 V AC/30 V DC,

1 A
• Minimum ON/OFF current: 100 mA
(24 V DC)

• Mechanical life: 20 million operations
  MIN. (100 operations/min)

• Electrical life: 100,000 operations
  MIN. (rated load)

• Output interlock: Unavailable

3.2 Digital output (DO)
(1) Number of outputs: Relay contact output
Up to 3 points (shared common)
Up to 2 points (independent common)
(2) Output specifications: Relay contact output
Contact structure: 1 NO (SPST) contact
Contact capacity: 220 V AC/30 V DC, 1 A Minimum Open/Close current: 100 mA
(24 V DC)
Mechanical life: 20 million operations MIN.
(100 operations/min)
Electrical life: 100,000 operations MIN.
(rated load)
(3) Output functions: Alarm output (see "Alarm function") Main unit control mode output,program status output, etc.
(4) Output cycle: 200ms

3.3 Auxiliary analog output (re-transmission output)
(1) Number of points: Up to 1 point
(2) Type: Current/voltage output (0 to 20 mA DC/4 to 20 mA DC/0 to 5 V DC/1 to 5 V  DC/ 0 to 10 V DC/2 to 10 V DC)

• Guaranteed output range: 0 to 20.6 mA DC/0 to 10.3 V DC

• Accuracy: ± 0.2%FS (± 5%FS at 1 mA or smaller)

• • Linearity: ± 0.2%FS (± 5%FS at 1 mA or smaller)

• Resolution: 5000 MIN.
• Load resistance: 600 Ù MAX. (current)

10 kÙ MIN. (voltage)
(3) Output cycle: 200 ms
(4) Output contents: PV, SV, DV, MV
(5) Additional function: Scaling function
(6) Limitation: Not selectable when using control output 2